Replacement gasket and nylon washers included for plug and play installation. The Low-Profile design protrudes only two inches from the stock taillight baseplate for a sleek, custom look on your rear fender. CUSTOM DYNAMICS TURN SIGNALS LICENSEAvailable with or without a top license plate illumination window. A new spherical internal lens design magnifies the light output to produce a bright red running and brake light and increased side visibility. This low-profile taillight offers 45 dual intensity red LEDs with a red or smoked lens and integrated amber turn signals. Re-install the cluster and test for function on the bike.Custom Dynamics Low Profile LED Taillight With Turn Signals For Harley.Cover solder connections with heat shrink tubing and use the heat gun to shrink the tubing.Strip back the insulation on both ends of wires, then twist together as follows: - The connector base end black wire will attach to the colored wire on the cluster - The connector base end colored wire will attach to the Black wire on the cluster.Next, you will need 2 pieces of heat shrink tubing to cover the connections, a soldering iron and a heat gun.Cut both wires on the 1156 cluster halfway between the connector base and the cluster.To correct this issue, we will modify the cluster. If reverse polarity is present, the test light should come on. Now touch the test probe to the ground wall contact.Touch the test probe to the center contact, the test light would normally light up here, but if we have reverse polarity, we will not have any current, so the test light will not come on.Attach the connection clamp from the test light to a ground stud or negative battery terminal on the bike.To remedy this condition, we need to confirm it by using a test light probe, then re-wire the cluster. When we have confirmed that there is power all the way to the turn signal socket, as well as confirmed that the LED cluster lights up, then reverse polarity is usually the issue. An LED cluster will only let electricity flow one way through, Positive to negative. So why does this not matter when we use incandescent bulbs? Well, incandescent bulbs are different from LED clusters in the respect that electricity can flow either way through the them, positive to negative or vice versa. The wires are, in effect, "reversed." This condition unintentionally occurs at the factory when the single intensity 1156 turn signals are installed. Reverse Polarity then is a term that describes an electrical condition in which the positive power wire is connected to the terminal on the receptacle intended for the ground wire and the ground wire is connected to the terminal on the receptacle intended for the positive power wire. Current flows from the positive pole to the negative pole. Polarity describes the direction in which electricity will flow. Touch the negative (-) to the base and positive (+) to the solder contact Motorcycle / Car battery with jumper wires) Too often, when motorcyclists want to replace their factory brake lights or turn signals, they settle for aftermarket options that provide little in the way of illumination and visibility. This combination of quality performance and premium style has made Custom Dynamics lighting a go-to for bike builders of all stripes. Using a 9 volt battery or 12 volt power supply ( ie. Their wide-ranging product offerings are designed to look good, provide maximum visibility, and make installation as easy as possible. Check that the ground connection tab is properly raised from the socket and in place.īench Testing the operation of the LED Cluster Using a NON CONDUCTIVE item, make sure the socket spring is moving up and down freely. CUSTOM DYNAMICS TURN SIGNALS FREEEnsure socket is free from Di-electric grease or corrosion.Ģ. If you have questions please call Custom Dynamics® at 1(800) 382-1388.ġ. An example of this is installing a PB-R-1156 and find there is no illumination with the LED when inserted into the 1156 socket. Please review this bulletin if you are no longer seeing proper illumination for one or all functions of the LED or you are in the process of installing the LEDs and find you are not getting the correct response from the LED. This bulletin is for the purpose of helping customers solve operation/connection issues on Custom Dynamics® LED replacement turn signal clusters with plug-in bases.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |